Shop by Category

Shop by Brand

Shop by Brand

STG 34k Parts and Accessories

stg34kmanual-diagram-page-02.jpg

  • Shown on original MG34 MG34 G10 Grip Set with Mounting Hardware (BROWN)

    MG34 G10 Grip Set with Mounting Hardware (BROWN)

    Newly Made MG34 Grip Set with Mounting Hardware. Includes: Left and Right Grip Panels made from  G10, a modern composite material which is total impervious to water, oil, solvent and most common chemicals. They are not injection molded plastic...

    $115.00
    Add to Cart
  • MG34 G10 Grip Set with Mounting Hardware (BLACK) MG34 G10 Grip Set with Mounting Hardware (BLACK)

    MG34 G10 Grip Set with Mounting Hardware (BLACK)

    Newly Made MG34 Grip Set with Mounting Hardware. Includes: Left and Right Grip Panels made from  G10, a modern composite material which is total impervious to water, oil, solvent and most common chemicals. They are not injection molded plastic...

    $115.00
    View Details
  • STG Universal Barrel Shroud - Steel 7.5" STG Universal Barrel Shroud - Steel 7.5"

    STG Universal Barrel Shroud - Steel 7.5"

    STG Universal barrel shroud for 4 lug trunions.  Loosely patterned after the Swedish M37 short-barreled Suomi setup. Fits all STG barrels greater than 8" long Material: Steel Finish: Black Oxide or Parkerized (grey) - Please Specify OAL: 7...

    $275.00
    Choose Options
  • Stemple Trunion Assembly - Slide Lock Pattern

    Stemple Trunion Assembly - Slide Lock Pattern

    Standard replacement Trunion Assembly for Stemple STG Standard Bolt Setups without pin mounts: Includes trunion, ejector, locking piece, locking pin, and spacer. Compatible with U9, 76, Stemple Suomi & 34k Stemple 76/45 setups without trunion mount...

    $390.00
    Add to Cart
  • Internally Threaded Pattern (ITP) Trunion Assembly Internally Threaded Pattern (ITP) Trunion Assembly

    Internally Threaded Pattern (ITP) Trunion Assembly

    Threaded Trunion Assembly for Internally Treaded Patter (ITP) setups This is the Trunion for Stemple STG ITP setups: U9, U9SF, U45, Stemple Suomi.   Includes: Threaded Trunion Trunion Locking Pin Ejector Standard Pattern

    $395.00
    Add to Cart
  • STG Universal Buffer and Key Plate Shim STG Universal Buffer and Key Plate Shim

    STG Universal Buffer and Key Plate Shim

    Included 1 x .003" thick Shim for: 1) Tightening the fit of the STG Buffer-to-Receiver fit.   2) Spacing the Key Plate rearward so it bottoms on the Buffer when the Castle Nut is tightened rather than the Lower Assembly.  If the Key Plate...

    $4.00
    Add to Cart
  • Spare Bottom Foam for STG Universal Case Spare Bottom Foam for STG Universal Case

    Spare Bottom Foam for STG Universal Case

    STG Universal Case Bottom Foam Adhesive backing can be used if desired by peeling the white cover. Cutouts for: M3 45acp mags x 2 kp31 drums x 2 kp31 mags x 2 universal mag housing - any type spare bolt bolt extension 10" barrel  without...

    $25.00
    Add to Cart
  • 9mm SMG Chamber and Headspace Gauge 9mm SMG Chamber and Headspace Gauge

    9mm SMG Chamber and Headspace Gauge

    9mm SMG Chamber Wear and Headspace Gauge To ensure the safe operation of 9mm Fixed-Firing-Pin (FFP) Blow-Back (BB) Submachine Guns (SMGs), chamber wear and headspace should be verified.   Since SMGs don't typically show a lot of bore wear...

    $36.00
    Add to Cart
  • KP31 Barrel Spacer For Use on Stemple STG Setups KP31 Barrel Spacer For Use on Stemple STG Setups

    KP31 Barrel Spacer For Use on Stemple STG Setups

    Given the difference between the Receiver and Trunion of an original KP31 and the Stemple 76/45, a Barrel Spacer that is approximately .4” long is necessary to use original KP31 Barrel Shrouds with the Stemple STG setups. Additional Barrel Shims...

    $12.75
    Add to Cart
  • U9 8.3" Barrel U9 8.3" Barrel

    U9 8.3" Barrel

    9mm  8.3" long barrel  41V50 Steel / Parkerized Finish Polished chamber and feed ramp 1:10 twist Loosely patterned after the Swedish M37 short-barreled Suomi setup and Carl Gustaf M45/Swedish K For use with 7.5" Steel...

    $150.00
    Add to Cart
  • KP31 Shroud Shim - .01" thick KP31 Shroud Shim - .01" thick

    KP31 Shroud Shim - .01" thick

    Copied from original parts and made from stainless steel.   Thickness .01"   This part tightens the barrel jacket to receiver fit by 'shimming' the rear of the barrel shroud to receiver/trunion.   This is a very useful part for...

    $4.85
    Add to Cart
  • S7 - STG Universal Extractor with Spring and Pin S7 - STG Universal Extractor with Spring and Pin

    S7 - STG Universal Extractor with Spring and Pin

    Newly manufactured extractor for all Universal configurations: U9, 34k, Stemple-Suomi, STG 76, U9SF, U45, U762, and post-2020 STG 1928s   Includes extra power Wolff spring and mounting pin.   Unlike the AR pattern extractors this has a more...

    $35.00
    Add to Cart
  • U9 8.64" barrel threaded 1/2"-28 U9 8.64" barrel threaded 1/2"-28

    U9 8.64" barrel threaded 1/2"-28

    9mm  8.64" long barrel  Stainless Steel Threaded .1/2"-28 on end Polished chamber and feed ramp 1:10 twist For use on 2010 pattern shroud  (see reference pic) and 7.5" Steel Shrouds

    $135.00
    Add to Cart
  • 1/2" - 28 thread extension 1" long

    1/2" - 28 thread extension 1" long

    Steel Thread Extension for 1/2" - 28 Threaded U9, U7.62 & 34k barrel  Features wrench flats for easy removal. (9/16" wrench) OAL: 1.4" Extends threads by 1"

    $21.00
    Add to Cart
  • 578" - 28 thread extension 578" - 28 thread extension

    578" - 28 thread extension

    Stainless Steel Thread Extension for 578" - 28 Threaded U9 and U45 Barrels.    Features wrench flats for easy removal. (3/4 wrench)   OAL: 1.2" Extends threads by .7"

    $25.00
    View Details
  • MG34 Trigger Spring MG34 Trigger Spring

    MG34 Trigger Spring

    Reproduction copy of original Trigger Spring: This is the spring that rests on the trigger spring base (fenderknoph) and inside the back of the trigger itself

    $4.95
    Add to Cart
  • 34k Stock Body with Butt Plate with Rubber Pad 34k Stock Body with Butt Plate with Rubber Pad

    34k Stock Body with Butt Plate with Rubber Pad

    New stock body and butt plate with rubber pad for the STG 34k setup with.  1/2" and 1" length rubber pads are available (1/2" pictured). Made from aluminum with hard anodize plating.  Features two points for use of modular quick-detachable...

    $235.00
    Add to Cart
  • 34k Butt Plate with Rubber Pad 34k Butt Plate with Rubber Pad

    34k Butt Plate with Rubber Pad

    New butt plate with rubber pad for the STG 34k setup with up/down adjustable butt plates.  1/2" and 1" length rubber pads are available (1/2" pictured). Made from aluminum with hard anodize plating.  Features two points for use of modular...

    $125.00
    Add to Cart
  • KP31 Shroud Shim - .002" thick KP31 Shroud Shim - .002" thick

    KP31 Shroud Shim - .002" thick

    Copied from original parts and made from stainless steel.   Thickness .002"   This part tightens the barrel jacket to receiver fit by 'shimming' the rear of the barrel shroud to receiver/trunion.   This is a very useful part for...

    $4.85
    Add to Cart
  • U9 10.35" barrel threaded 1/2"-28 U9 10.35" barrel threaded 1/2"-28

    U9 10.35" barrel threaded 1/2"-28

    9mm 1:10 twist Threaded 1/2"-28 10.35" long barrel  41V50 Steel / Parkerized Finish Polished chamber and feed ramp Compatible with all shroud setups except for the long KP31 pattern shrouds    Ideal for use with direct thread...

    $160.00
    Add to Cart
  • Suomi 36 rd stick magazine

    Suomi 36 rd stick magazine

    36rd original Finnish Suomi drum. Works with M31/KP31, KP44, M37/39, M45. (not for sale where prohibited) Excellent condition       MAGAZINE SHIPPING RESTRICTIONS   California Restrictions: 10 rounds, unless you can...

    $28.50
    View Details
  • KP31 Barrel Shim - .001 thick KP31 Barrel Shim - .001 thick

    KP31 Barrel Shim - .001 thick

    Copied from original parts and made from stainless steel.   Thickness .001"    These are the most thin we could make.  They are excellent for fine tuning your barrel to trunion to shroud fit.   This part tightens the barrel...

    $2.75
    Add to Cart
  • 1/2" - 28 thread protector

    1/2" - 28 thread protector

    Stainless Steel Thread Protector & Flash Hider for 1/2" - 28 Threaded for U9 and U7.62 10" and 16" barrels   Features wrench flats for easy removal.

    $25.00
    Add to Cart
  • 578" - 28 thread protector 578" - 28 thread protector

    578" - 28 thread protector

    Stainless Steel Thread Protector & Flash Hider for 578" - 28 Threaded U9 and U45 Barrels.    Features wrench flats for easy removal.

    $25.00
    Add to Cart
  • KP31 Shroud Shim - .005" thick KP31 Shroud Shim - .005" thick

    KP31 Shroud Shim - .005" thick

    Copied from original parts and made from stainless steel.   Thickness .005"   This part tightens the barrel jacket to receiver fit by 'shimming' the rear of the barrel shroud to receiver/trunion.   This is a very useful part for...

    $4.85
    Add to Cart
  • Stemple STG 9mm Barrel 12.75" Stemple STG 9mm Barrel 12.75"

    Stemple STG 9mm Barrel 12.75"

    12.75" barrel for BRP Stemple Takedown Guns.  FULL AUTO CHAMBER SPEC.   Extractor Location The extractor relief on this barrel is setup for the BRP-Stemple extractors and would have to be enlarged to accommodate the KP31 extractor for...

    $160.00
    Add to Cart
  • Stemple STG 9mm Barrel 16" Threaded 1/2-28 Stemple STG 9mm Barrel 16" Threaded 1/2-28

    Stemple STG 9mm Barrel 16" Threaded 1/2-28

    16" barrel for BRP Stemple Takedown Guns.  Works with slant pattern KP31 shroud.  Will work with compensated shroud if the exit hole is opened to .635".   Extractor Location The extractor relief on this barrel is setup for the...

    $135.00
    View Details
  • PIAT Cleaning Brush PIAT Cleaning Brush

    PIAT Cleaning Brush

    Original PIAT bristle brush. Approximately 12" long with 1.5" diameter brush.      Also, very useful for cleaning the inside of MG34 & MG42 barrel jackets, and BREN receivers.

    $4.50
    Add to Cart